rpc00104: Arabidopsis thaliana MM2d-LS cell suspension culture

Note

  • Components

    • Domestic delivery: A 50-mL plastic conical centrifuge tube, containing cell suspension

    • Overseas delivery: A 250-mL plastic Erlenmeyer flask, containing cells placed on semi-solid medium

  • Notice

    • Subculture the cells to fresh medium immediately after arrival.

    • Do not store the cell culture in a refrigerator and a freezer.

    • Maintain aseptic conditions of the cell culture, and work in a laminar flow cabinet.

  • Method

    • Culture medium: mLS medium, 0.2 mg/L 2,4-D, pH 5.8 (medium no. 1)

    • Culture conditions: 27°C, dark, 130 rpm

    • Subculture: 7-day intervals

  • Citation of cell line

    When results obtained by using this cell line are published in a scientific journal, it should be cited in the following manner: “Arabidopsis thaliana MM2d-LS cell line (rpc00104) was provided by the RIKEN BRC through the National BioResource Project of the MEXT, Japan.”

Introduction

Arabidopsis MM2d-LS cell line was established by subculturing the MM2d cells in a different culture medium (Adachi et al. 2011 [1]). The parent MM2d cell line (rpc00103) was established from a stem of Arabidopsis thaliana (L.) Heynh. accession Landsberg erecta (Menges and Murray 2002 [2]). The MM2d-LS cell line can be used for cell cycle synchronization and genetic transformation (Adachi et al. 2011 [1]). The MM2d-LS cells are grown in a modified Linsmaier and Skoog (mLS) medium supplemented with 0.2 mg/L 2,4-dichlorophenoxyacetic acid (2,4-D), pH 5.8. Our MM2d-LS cell culture has been maintained in the dark at 27°C with rotary shaking at 130 rpm and subcultured at 7-day intervals.

Materials

Chemicals and stock solutions

(All stock solutions are stored at 4°C)

  • MS salt mix

    Murashige and Skoog Plant Salt Mixture, FUJIFILM Wako Pure Chemical Corporation (#392-00591)

  • Sucrose

  • BY2_P

    Chemical

    Concentration (mg/mL)

    KH2PO4

    80

  • LS_VT_modified

    Chemical

    Concentration (mg/mL)

    Thiamine·HCl

    0.4

    myo-Inositol

    40

  • 2,4-D (0.2 mg/mL)

    Chemical

    Concentration (mg/mL)

    2,4-D sodium monohydrate

    0.236

    (2,4-Dichlorophenoxy)acetic acid sodium salt monohydrate, Sigma-Aldrich (D6679)

  • KOH (1 N)

Glassware

  • Erlenmeyer flask (300 mL), capped with two layers of aluminum foil

  • Pipette (10 mL; large tip opening) and a bulb, sterilized by autoclaving at 121°C for 20 min

Preparation of mLS medium (medium no. 1)

  1. Dissolve the following chemicals in approximately 800 mL of distilled water.

    Chemical

    Amount

    MS salt mix

    1 bag (1 L)

    Sucrose

    30 g

  2. Add following stock solutions, and fill up to approximately 950 mL with distilled water.

    Stock solution

    Volume (mL)

    BY2_P

    2.5

    LS_VT_modified

    2.5

    2,4-D (0.2 mg/mL)

    1

  3. Adjust the pH of the solution to 5.8 with KOH (1 N), and fill up to 1 L with distilled water.

  4. Pour 50 mL of the medium into a 300-mL flask.

  5. Autoclave the flask at 121°C for 20 min.

Methods

  1. Agitate a 7-day-old culture well and transfer 1 mL of cell suspension to 50 mL of fresh mLS medium with a pipette.

  2. Incubate cell cultures on a rotary shaker at 130 rpm under the dark condition at 27°C.

Notes

  • For domestic customers: We send MM2d-LS cell suspension in a 50-mL disposable conical centrifuge tube. The cells should be transferred to fresh mLS medium immediately after arrival.

  • For overseas customers: We send MM2d-LS cells placed on semi-solid mLS medium in a 250-mL disposable Erlenmeyer flask. The cells should be transferred to fresh mLS medium immediately after arrival. Collect the cells from the semi-solid medium with a spatula and transfer them to Erlenmeyer flasks containing fresh liquid medium.

  • In order to maintain MM2d-LS cell suspension cultures stably, it is essential to transfer an adequate amount of cells to fresh mLS medium in every subculture. The amount of cells may vary from one lab to another, because proliferation of MM2d-LS cells is affected by culture conditions, such as a room temperature, rotation speed of a rotary shaker, and aeration condition of the culture.

  • In order to obtain good aeration of a suspension culture, a silicone sponge plug may be used instead of the aluminum foil cap (e.g., cap-type Silicosen; Shin-Etsu Polymer, Tokyo, Japan).

Genotyping

Maintenance history

References

Protocols